ABS Core
Warm White
- Nozzle
- 245–265 °C
- Bed
- 95–110 °C
- Chamber
- 45–55 °C
- Speed
- 40–90 mm/s
- Cooling
- 0–20 %
- Drying
- 70 °C / 4 h
- Batch
- issued per lot at dispatch
ZV-ABS-CO-WWH · scan / learn / make
ZV-ABS-CO-WWH
ABS & ASA · ABS Core
ABS CoreWarm White
Paints and primes cleanly for enclosures that get a finish coat.
On request
for pricing and minimum order
1 000 g · Gloss
Diameter
1,75 mm
Other colours in ABS Core
Print settings
- Nozzle
- 245–265 °C
- Bed
- 95–110 °C
- Chamber
- 45–55 °C
- Speed
- 40–90 mm/s
- Cooling
- 0–20 %
- Drying
- 70 °C / 4 h
- Diameter
- 1,75 mm
Print settings are the common starting window for this material class, not measurements. Calibrate with a temperature tower and a flow test on your own machine.
Properties
- Density
- 1,04 g/cm³ISO 1183 · PolyLite™ ABS
- Tensile strength
- 33,4–34,9 MPaISO 527 · XY · PolyLite™ ABS – ABS Pro
- Tensile modulus
- 2 247 MPaISO 527 · XY · PolyLite™ ABS
- Elongation at break
- 17,9 %ISO 527 · XY · PolyLite™ ABS
- Bending strength
- 56,2 MPaISO 178 · XY · PolyLite™ ABS
- Heat deflection (HDT)
- 100–106 °CHDT 0,45 MPa · PolyLite™ ABS – ABS Pro
- Impact strength
- 17,3–18,0 kJ/m²ISO 179 · notched, XY · PolyLite™ ABS – ABS Pro
- Vicat softening
- 104–116 °CPolyLite™ ABS – ABS Pro
Benchmarked on published grades: Polymaker PolyLite™ ABS, Polymaker ABS Pro · Polymaker · 27/08/2026
ABS Core
Heat resistant, easy to sand, glues with acetone into a single piece. The classic engineering plastic, and still the cheapest route past 90 °C.
Best for
- Enclosures near electronics and motors
- Parts that get machined or bonded after printing
- Vacuum forming patterns
Watch out
Warps hard without chamber heat, and needs ventilation while printing.
Enclosure 45–55 °CVentilation
Warm White · #f0ece2
The properties on this page are values published in the named manufacturers' data sheets, measured on their grades to the standard printed against each row — not measurements of a ZORVA spool. Use them to compare material classes, not as an acceptance specification.
Passport
Ships with the spool. Published before you buy.
The same record on the label, on this page and in the box. Batch number included, so a bad print can be traced to a specific run.
ABS Core
- Code
- ZV-ABS-CO-WWH
- Net weight
- 1 000 g
- Diameter
- 1,75 mm
- Finish
- Gloss
- Colour value
- #F0ECE2
- Polymer
- Acrylonitrile butadiene styrene / acrylonitrile styrene acrylate
- Process
- FDM (filament)
Also in
More ABS/ASA.
ABS Core
Graphite
Acetone smoothing turns layer lines into a moulded surface.
GlossOn request
ASA Core
Slate Grey
Holds colour in direct sun where grey PLA chalks out within a season.
MatteOn request
ASA Core
Arctic White
Reflects heat, which matters for sensor housings in the sun.
MatteOn request
ASA Core
Signal Orange
UV-stable orange for outdoor markers and safety hardware.
MatteOn request