High Temp Resin
Slate
- Layer height
- 0,05 mm
- Exposure
- 3.0–4.0 s @ 8K mono
- Bottom layers
- 6 @ 35 s
- Lift speed
- 45 mm/min
- Resin temperature
- 30–35 °C
- Wash
- 4 min IPA
- Batch
- issued per lot at dispatch
ZV-RES-HT-SLT · scan / learn / make
ZV-RES-HT-SLT
Resin · High Temp Resin
High Temp ResinSlate
Colour is stable through the 120 °C thermal post-cure.
On request
for pricing and minimum order
1 000 g · Matte
Diameter
Bottle
Print settings
- Layer height
- 0,05 mm
- Exposure
- 3.0–4.0 s @ 8K mono
- Bottom layers
- 6 @ 35 s
- Lift speed
- 45 mm/min
- Resin temperature
- 30–35 °C
- Wash
- 4 min IPA
- Cure
- 6 min @ 405 nm, then 120 °C / 2 h
- Volume
- 1 000 g bottle
Print settings are the common starting window for this material class, not measurements. Calibrate with a temperature tower and a flow test on your own machine.
Properties
- Tensile strength
- 58,3 → 51,1 MPaASTM D638-14 · UV cure → plus 160 °C thermal cure
- Elongation at break
- 3,3 → 2,4 %ASTM D638-14 · UV cure → plus 160 °C thermal cure
- Flexural modulus
- 2 760 MPaASTM D790 · UV cure → plus 160 °C thermal cure
- Impact strength
- 18,2 → 24,2 J/mNotched Izod · UV cure → plus 160 °C thermal cure
- Heat deflection (HDT)
- 142 → 238 °CHDT 0,45 MPa · UV cure → plus 160 °C thermal cure
Benchmarked on published grades: Formlabs High Temp Resin · Formlabs · 27/08/2026
High Temp Resin
For fixtures that go near heat: thermoforming moulds, soldering jigs, flow test parts. Heat deflection above 200 °C after a full thermal post-cure.
Best for
- Thermoforming and casting moulds
- Soldering and reflow fixtures
- Airflow and thermal test parts
Watch out
The 200 °C figure needs the thermal post-cure step. Straight out of the UV chamber it is far lower.
405 nm MSLA or DLPThermal post-cure ovenNitrile gloves
Slate · #5b5f66
The properties on this page are values published in the named manufacturers' data sheets, measured on their grades to the standard printed against each row — not measurements of a ZORVA spool. Use them to compare material classes, not as an acceptance specification.
Passport
Ships with the spool. Published before you buy.
The same record on the label, on this page and in the box. Batch number included, so a bad print can be traced to a specific run.
High Temp Resin
- Code
- ZV-RES-HT-SLT
- Net weight
- 1 000 g
- Diameter
- Bottle
- Finish
- Matte
- Colour value
- #5B5F66
- Polymer
- Photopolymer for MSLA and DLP
- Process
- Resin (MSLA / DLP)
Also in
More Resin.
Precision Resin
Precision Grey
Neutral grey photographs detail better than any other resin colour.
MatteOn request
Tough Resin
Onyx
Dark parts hide support marks, which matters on functional prototypes.
MatteOn request
Castable Resin
Amber
Translucent amber so you can inspect prongs and settings before casting.
TranslucentOn request